How to Lower Restoration Hardware Crib

Are you expecting a baby and have recently purchased a restoration hardware crib but can’t seem to lower it? Or maybe your little one is getting bigger and the current height of their crib doesn’t give them enough space.

How to Lower Restoration Hardware Crib

In either case, if you need help lowering your Restoration Hardware crib, this post provides step-by-step instructions on how to lower restoration hardware crib! First, take out all the parts needed for assembly such as screws and tools then use our expert tips provided in this blog post to ensure proper installation of your beautiful new piece of furniture. Soon you’ll be rocking a happy tired baby off into dreamland in no time!

Tools and materials you will need to lower restoration hardware crib

  1. Phillips screwdriver
  2. Flathead screwdriver
  3. Allen wrench
  4. Replacement screws (if necessary)
  5. A level (optional)

Step-by-Step Guidelines on How to Lower Restoration Hardware Crib

Step 1: Check for Any Visible Screws or Bolts

Before you start to lower your restoration hardware crib, take a few moments to check for any visible screws or bolts. If there are, unscrew them using a Phillips screwdriver or an Allen wrench and set them aside. Checking for screws or bolts beforehand can save you a lot of time when it comes to the actual lowering process. If you find any missing screws, replace them with new ones before continuing.

Step 2: Loosen the Corner Posts

Once all visible screws have been removed or replaced, you can move on to loosening the corner posts. This part is crucial for safety and balance, so take your time at this step and make sure each post is loosened evenly. Use a flathead screwdriver if necessary to help you loosen the posts but don’t force it too much as this may cause damage.

Step 3: Lower the Corner Posts

Once all four corner posts have been loosened, you can begin to lower them one by one. Make sure that each post is lowered evenly and that the crib doesn’t become unbalanced. If necessary, use a level to make sure that all four posts are even with one another. In this step, it is also important to make sure that all replacement screws or bolts are in place and all tools have been removed.

Use a Level to Make Sure

Step 4: Check for Any Additional Pieces

Once the corner posts have been lowered, take a few moments to check for any additional pieces such as end panels or side rails. Make sure these pieces are securely in place before moving on to the final step.

Step 5: Test the Crib

Finally, test your newly lowered crib to make sure that it is balanced and secure. Place a few toys or books onto the mattress and shake gently to ensure that everything is securely in place. If you find any loose pieces, take a moment to tighten them before using the crib.

Congratulations! You have successfully lowered your Restoration Hardware Crib. Enjoy your new piece of furniture and happy parenting!

We hope this step-by-step guide was helpful in teaching you how to lower the restoration hardware crib. Always remember to practice safety when working with furniture, especially when it comes to your baby’s crib. If you have any questions or comments, please feel free to leave them below!

Additional Tips and Tricks to Lower Restoration Hardware Crib

1. Use a socket wrench to loosen the screws that secure the crib’s side panels to its headboard and footboard. This will allow you to adjust the height of the mattress more easily.

2. Loosen the adjustment bolts located at each corner of your Restoration Hardware crib’s frame. These are typically found near the mattress support. Turn the bolts counterclockwise using an adjustable wrench to lower the crib.

3. Adjust your crib’s mattress platform height if you have access to a compatible version of Restoration Hardware’s specially designed adjustment tool. This tool is designed to smoothly adjust mattress heights with minimal effort and no danger of overtightening or loosening the bolts.

4. Place a piece of plywood between the mattress and its bed frame if you don’t have access to an adjustable tool. This will lower the mattress height, which is particularly useful for toddlers transitioning from a crib to a toddler bed.

Place a Piece of Plywood Between the Mattress

5. Lower your Restoration Hardware crib further by changing out the springs, if necessary. Purchase a set of new, lower-profile crib springs and follow the instructions provided in your crib’s assembly manual to install them.

6. Measure the height of your baby from head to toe regularly throughout his or her infancy and early childhood. This will ensure that you adjust the mattress height accordingly as your baby grows, helping to prevent a fall from the crib.

7. Finally, use common sense when lowering a Restoration Hardware crib. Make sure that the mattress doesn’t get too low—a height of more than five inches off of the floor could cause injury if your child were to fall out of bed. Additionally, avoid using any items to prop up the mattress if you need to lower it further than five inches—this could be a safety hazard. Always adjust the legs of your crib or installation tools provided by Restoration Hardware instead.

By following these tips and tricks, you’ll be able to safely and securely lower your Restoration Hardware Crib with ease for your baby’s optimal comfort.

Precautions Need to Follow for Lowering Restoration Hardware Crib

1. Before attempting to lower the crib, make sure that all of the necessary safety measures are in place. Check for any loose screws or hardware and tighten them as needed. Ensure that the mattress is securely attached to the frame and that it will stay in place when moved.

2. Gather a couple of sturdy helpers to assist you in the lowering process. One person should be positioned at the bottom of the crib and one at the top. The person at the bottom should hold onto the mattress securely as it is lowered, while the other person guides it down evenly.

3. Gradually lower the crib to its lowest setting using a slow and steady motion. Make sure the crib frame is supported and does not become unstable.

4. Utilize a level to ensure that the crib is lowered correctly and that it sits evenly on the floor once in its new position.

Utilize a Level to Ensure That the Crib is Lowered Correctly

5. Check for any additional screws or hardware that may need tightening after the lowering process is complete. Make sure all of the bolts, nuts, and screws are secure.

6. Finally, check the crib mattress for any rips or tears that may have been caused by the lowering process. If there are any signs of damage, replace them immediately to ensure a safe sleeping environment for your child.

Take the time to read through the manufacturer’s instructions before attempting any modifications or adjustments to your crib. This will help ensure that you are following proper protocols for the safety of you and your baby.

Frequently Asked Questions

Is It Possible to Lower the Restoration Hardware Crib? 

Yes, most Restoration Hardware cribs come with adjustable mattress heights. This allows you to easily lower the mattress height as your baby grows. To do this, simply refer to the manufacturer’s instructions and use an Allen wrench to adjust the mattress height.

How Low Can I Lower the Crib?

Restoration Hardware cribs usually have two to four-height settings, depending on the model you purchase. Each set is typically three to five inches apart, so you can lower the mattress up to 12 inches in some models. It’s important to double-check your product manual for exact measurements.

Is Lowering the Crib Safe?

Yes, lowering the crib is safe as long as you follow the manufacturer’s instructions and use the appropriate tools to adjust the mattress height. Make sure that your baby can’t climb out of the crib before you lower it. Additionally, if your Restoration Hardware crib has a toddler rail, you may need to purchase a conversion kit in order to lower the mattress.

What If I Don’t Want to Lower the Crib?

If you have a Restoration Hardware crib and don’t want to adjust the mattress height, there are other safety measures you can take. You can use crib bumpers or blankets on either side of your baby to prevent them from rolling out of the crib. Additionally, you can use a sleep positioner that keeps your baby in the center of the crib for added safety and comfort.

You Can Use Crib Bumpers


Taking the time to familiarize yourself with how to lower Restoration Hardware crib is an important and necessary step for ensuring the safety of your baby, and it will pay off in the long run. With just a few steps, you can quickly become familiar with this process and be ready to lower your crib when needed. Remember to use caution any time you interact with your baby’s crib.

Always follow instructions precisely and double-check that each lever or knob is secure before leaving the room, and don’t forget to clear away all hazardous or sharp objects in or around the crib before moving it. With regular maintenance and adjustments as necessary, you can rest assured that your Restoration Hardware crib is providing a safe place for your little one to sleep soundly.

Photo of author

Loren Jones

Hi, my name is Loren. I live with my husband and 4 lovely kiddos in the Eastern part of San-fransisco. I have a smart beautiful,curious 6 year old daughter, a handsome 11-year-old son, an intelligent and tech geek 15 years old son and a creative, artistic 12-year-old stepson. With each of my kids being five years apart, I feel that I’m now continually phasing in and out of each stage of parenting! I’ve learned a lot about the way children learn and behave, especially in a school setting with regards to curriculum. I enjoy sharing that insight through my writing and hope that it can help others.

Leave a Comment